Decarburization on surface layers can affect heat treatment and hardness attained on parts. Decarburization also provides evidence of where in a process a defect or imperfection occurred.
Most defects in steel workpieces encountered in our precision machine shops are longitudinal in nature. While their presence alone is enough to concern us, for the purposes of corrective action, it becomes important to identify where in the process the longitudinal imperfection first occurred. Visual examination alone is not enough to confirm the source. Did it occur prior to rolling? During rolling? After rolling? Understanding decarburization and how it presents in a sample can help us to identify where and when in the process the imperfection first occurred.
The question that we want to answer as part of our investigation is usually “When in the process did the defect first occur?” Looking at decarburization and any subscale present can help us answer that question with authority.
What is Decarburization?
“Decarburization is the loss of carbon from a surface layer of a carbon containing alloy due to reaction with one or more chemical substances in a medium that contacts the surface.”– Metals Handbook Desk Edition
The carbon and alloy steels that we machine contain carbon. In the photo above, the carbon is contained in the pearlite (darker) grains. The white grains are ferrite. In an etched sample, decarburization surrounding a defect is identified as a layer of ferrite with very little, or none of the darker pearlitic structure typically seen in the balance of the material. The black intrusion in the photo above is the mount material that has filled in the crevice of the seam defect.
What is Subscale?
Subscale is a reaction product of Oxygen from the atmosphere with various alloying elements as a result of time at high temperatures. The presence or absence of the subscale is the indicator that helps us to pinpoint the origin of the defect. For a subscale to be present, the time at temperature must be sufficient for oxygen to diffuse and react with the material within the defect. According to Felice and Repp, 2250 degrees F and fifteen minutes is necessary to develop an identifiable subscale. Lower temperatures would require longer times. Typically rolling mill reheat cycles offer plenty of time to develop a subscale in a prior existing defect. However, for defects that are created during rolling, the limited time at temperature and the decreasing temperatures on cooling make formation of subscales unlikely.
Reading Decarb and Subscale to Understand the Defect
Decarburization is time and temperature dependent. This means that its relative depth and severity are clues as to time at temperature, though interpretation requires experience and understanding of the differences in appearance from grade to grade based on Carbon content.
Symmetrical Decarburization
If the decarburization is symmetrical this is an indication that the defect was present in billet or bloom prior to reheat and rolling. oxygen in the high temperature atmosphere of the reheat furnace depletes the carbon equally from both sides of the pre-existing defect.
Asymmetrical Decarburization
Decarburization that is obviously asymmetrical indicates that the defect is mechanical in nature and was induced some time during the hot rolling process.
Ferrite Fingers
Ferrite fingers are a surface quality problem that is associated with longitudinal bar defects. During reheat, a defect in the bllom or billet is exposed to high temperature atmosphere, forming decarburization and subscale around the defect. Rolling partially closes or “welds shut” the crack. However, a trail of of subscale is entrained in a formation of almost pure ferrite which has been depleted of pearlite, carbon and alloy by the reaction at elevated temperature. This trapped scale remains a potential oxygen source, driving further internal oxidation and decarburization if temperatures remain high.
Continuous improvement requires taking root cause corrective action. Obviously identifying the root cause is critical. When we encounter longitudinal linear defects in our steel products, using a micro to characterize the nature of the decarburization and presence or absence of sub scale or ferrite fingers are important evidence as to when, where, and how in the process the defect originated.
Tag: AISI Rod and Bar Surface Defects Definition
“Slivers are elongated pieces of metal attached to the base metal at one end only. They normally have been hot worked into the surface and are common to low strength grades which are easily torn, especially grades with high sulfur, lead and copper.”- AISI Technical Committee on Rod and Bar Mills, Detection, Classification, and Elimination of Rod and Bar Surface Defects
Slivers may be caused by bar shearing against a guide or collar, incorrect entry into a closed pass, or a tear due to other mechanical causes. Slivers may also be the result of a billet defect that carries through the hot rolling process.
Slivers often originate from short rolled out point defects or defects which were not removed by conditioning.
Billet conditioning that results in fins or deep ridges have also been found to cause slivers and should be avoided. Feathering of of deep conditioning edges can help to alleviate their occurrence.
Slivers often appeared on mills operating at higher rolling speeds.
When the frequency and severity of sliver occurrence varies between heats, grades, or orders, that is a clue that the slivers probably did not originate in the mill.
Slivers are often mistaken for shearing, scabs, and laps. We will post about these other defects in the future.
“Laps are longitudinal crevices at least 30 degrees off radial, created by folding over, but not welding material during hot working (rolling). A longitudinal discontinuity in the bar may exist prior to folding over but the defect generally is developed at the mill.”- AISI Technical Committee on Rod and Bar Mills, Detection, Classification, and Elimination of Rod and Bar Surface Defects
In plain language, a lap is a ‘rolled over condition in a bar where a sharp over fill or fin has been formed and subsequently rolled back into the bar’s surface.’
An etch of the full section shows what is going on in the mill. Laps were often related to poor section quality on incoming billets, although overfill scratches, conditioning gouges from “chipping” have also been shown to cause laps.
Laps are often confused with slivers, and mill shearing which we shall describe and post soon.
The term ‘lap seam’ is sometimes used, but it is careless usage; it implies the lap is caused by a seam – it is not; a seam is a longitudinally oriented imperfection, and so is used in this mongrel term as a shorthand way of saying ‘longitudinal.’
Modern speakers sometimes try to use the word ‘lamination’ to describe laps but as we will see, not all lamination type imperfections are laps…